EDC16 Pinout (EDC16C1, C31, C35, CP35 Bench Pinout)

Bench pinout for Bosch EDC16 diesel ECUs used in BMW and MINI: EDC16C1, EDC16C31 (DDE5), EDC16C35 and EDC16CP35 (DDE6). All four can be bench flashed over either K-Line or D-CAN, so pick the wiring that suits your setup. Power and ground are the same for both; only the communication pins change. Two pins are numbered 1 on different connectors, so use the images to find the right one.

EDC16 K-Line bench pins

EDC16 K-Line bench pinout diagram showing 12V power pins, ground pin 4 and K-Line pin 2
EDC16 bench pinout – K-Line connection.
FunctionEDC16 (K-Line) pin(s)
+12 VPin 1 (see image)
+12 VPin 1 (see image)
GroundPin 4
K-LinePin 2

EDC16 D-CAN bench pins

EDC16 D-CAN bench pinout diagram showing 12V power pins, ground pin 4, CAN High pin 14 and CAN Low pin 1
EDC16 bench pinout – D-CAN connection.
FunctionEDC16 (D-CAN) pin(s)
+12 VPin 1 (see image)
+12 VPin 1 (see image)
GroundPin 4
CAN HighPin 14
CAN LowPin 1 (see image)

Which cars use EDC16?

EDC16C31 and EDC16C1 (DDE5) are used in E46, E53, E60, E65 and E83 BMW diesels. EDC16C35 and EDC16CP35 (DDE6) are used in E60, E70, E87 and E90 BMWs and MINI diesels. Not sure what you have? Use our ECU identification guide.

How to bench flash an EDC16 over K-Line

  1. Connect a stable 12 V supply to ECU both power pins (pin 1, see image), and to the KDCAN cable’s 12 V pin (OBD pin 16).
  2. Connect ground to ECU pin 4, and to the KDCAN cable’s ground (OBD pins 4 and 5).
  3. Connect the KDCAN cable’s K-Line (OBD pin 7) to ECU pin 2.
  4. Open DDE5 Quickflash or DDE6 Quickflash and read or flash the ECU as you would over OBD.

How to bench flash an EDC16 over D-CAN

  1. Connect a stable 12 V supply to ECU both power pins (pin 1, see image), and to the KDCAN cable’s 12 V pin (OBD pin 16).
  2. Connect ground to ECU pin 4, and to the KDCAN cable’s ground (OBD pins 4 and 5).
  3. Connect the KDCAN cable’s CAN High (OBD pin 6) to ECU pin 14.
  4. Connect the KDCAN cable’s CAN Low (OBD pin 14) to ECU pin 1 (see image).
  5. Open DDE5 Quickflash or DDE6 Quickflash and read or flash the ECU as you would over OBD.

The KDCAN cable needs 12 V and a ground shared with the ECU to communicate, just like it gets from the OBD port in the car. Tip: double-check every connection with a multimeter before powering up, and use a power supply rather than a weak battery charger.

Do I need to bench flash?

Usually not. DDE5 Quickflash (EDC16C31/C1) and DDE6 Quickflash (EDC16C35/CP35) work through the OBD port. The bench pinout is for ECUs that are out of the car, being tested, or recovering from a failed flash.

Related EDC16 tools